Acceptable Quality Level (AQL) in Garment Industry
Noor Ahmed Raaz
Asst. Prof, Dept. of Textile Engineering,
Atish Dipankar University of Science & Technology
Email: raju.uttara105@gmail.com
Acceptable Quality Level (AQL):
AQL means Acceptable Quality Level. AQL is one of the most frequently used terms when it comes to quality in the garment export industry. As most of the acceptance decisions of the apparel shipments for the export market are made on the basis of AQL based sampling plans. In any business process, before accepting the finished goods from the manufacturer buyer do inspection of goods. AQL is so much important in export oriented garment industry. Because foreign buyers are so much concern about product quality. They give AQL on the product to the manufacturer. Buyers do inspection of goods as randomly process. If AQL pass that means goods are in acceptable quality level he gives certificate to ship the goods. The AQL level varies process to process, product to product and even buyer to buyer in garment industry. In the following table a sampling plan is given for final shipment inspection.
Associated with statistical sampling of apparels, acceptance quality level (AQL) is the “minimal standard for a satisfactory process or product average”. Acceptance Quality Level (AQL) refers to the maximum number of defective items that could be considered accepted during the random sampling of and inspection. The defects that are found during inspection are classified into 3 categories:
Critical: Must be 100% accurate. There is no range.
Major: Normally 2.5%
Minor: Normally 4%
Sampling Method:
Single Sampling method
Double Sampling method
Multiple Sampling method
Table: AQL chart in garment industry for shipment inspection
Lot or Batch size
Sample size Code Letter
Sample Size
Acceptable Quality level
2.5
4.0
6.5
Ac
Re
Ac
Re
Ac
Re
2 – 8
A
2
0
1
0
1
0
1
9 – 15
B
3
0
1
0
1
0
1
15 – 25
C
5
0
1
0
1
0
1
26 – 50
D
8
0
1
1
2
1
2
51-90
E
13
1
2
1
2
2
3
91-150
F
20
1
2
2
3
3
4
151-280
G
32
2
3
3
4
5
6
251-500
H
50
3
4
5
6
7
8
501-1200
J
80
5
6
7
8
10
11
1201-3200
K
125
7
8
10
11
14
15
3201-10000
L
200
10
11
14
15
21
22
10001-35000
M
315
14
15
21
22
21
22
Source: ANSI/ASQ Z 1.4 The Sampling procedures and table for inspection by attributes
How to Read AQL Table?
It is very easy process. Now terms of AQL table are given below:
1. Lot or Batch size: This means total how many pieces inspector is going to check or inspect.
2. Sample size Code letter: This code is indicative a range of batch size.
3. Sample size: It means that how many pieces will be picked up for inspection from the total offered pieces (Batch).
4. Ac (Accepted): The number in this column denotes that if the inspector finds up to that much defective pieces the shipment will be accepted by buyer.
5. Re (Rejected): On the other hand, number in this column denotes that if the inspector finds that much defective pieces or more than the listed number, the shipment will be rejected (or asked to the manufacturer for 100% inspection and re-offer for final inspection) by buyer.
AQL Requirements Based on the Products:
In general cases the buyer will determine which sampling plan and what AQL to adopt. There are three types of sampling plans: i.e. single, double and multiple sampling plans. Each sampling plan can be performed at three levels, i.e. normal, tightened and reduced, depending on inspection requirements and quality of the products. The apparel industry mainly uses single sampling plans for the acceptance decisions. However, a few buyers also use double sampling procedure. In single sample based on AQL table you randomly draw a sample consisting of specified number of garments from a lot. The sample plan also provides the number maximum allowed defective pieces. If the defective pieces are less than allowed number the lot is accepted and if the number of defective pieces is greater than allowed the lot is rejected. One may say that as the acceptance sampling is scientific, ideally speaking, it must lead to 100% reliable results. In other words, it must always lead to acceptance of lots containing lower defective level than AQL and must reject all the lots that contain more defective products than AQL. But this is not possible, as the acceptance decision is made only on the basis of small sample drawn from the lot and it carries a risk of making a wrong judgment.
Single sampling plan – Normal inspection:
Assurance an AQL of 2.5 % and a lot size of 1200 garments and the sample size is 80 garments. If the number of defective garments found is 5 the total lot is “Acceptable” suppose if the defective garments found is 6, the total lot is “Reject/ Re-Check”.
Double sampling plan – Normal Inspection:
Assurance an AQL 4.0% and a lot size is 1200 garments and the sample size is 80 garments. If the Number of defective garments found is 7, the total lot is “Acceptable” suppose if the defective garments found is 8 the total lot is “Reject/ Re-Check”.
For Example:
Total garments (lot Size) 1200 garments
Sample size (selected for inspection) 80 garments
AQL 2.5 / 4.0
If the major defective found is 5 and minor defective found is 7 the total garments is “Acceptable”. If the defective exceeds (Above 5 major and 7 Minor), the total garments is Reject / Re-check.
What AQL is Not?
Having known what is AQL? How does it work? How to succeed in AQL based inspections? It is equally important to now, as indicated below, what AQL is not:
A permit to ship defective goods to the tune of agreed AQL level: AQL 4.0 does not mean that supplier has a right to send up to 4% defective merchandise to customer / buyer.
A guarantee that all shipments passed as per AQL plan will definitely contain lower percent defective than the specified AQL. There is also no guarantee that lots with higher percentage defective will not pass on AQL inspection.
An indicator of the quality level achieved by a manufacturer. Let us assume that the average rate of defective garments in a manufacturer’s shipment is 6%, but the AQL used by buyer for final inspection is 2.5. It is possible that the manufacturer may resort to 100% inspection of the merchandise to weed out the defective garments so that the shipment can pass the final inspection by the buyer at AQL 2.5.
Founder & Editor of Textile Learner. He is a Textile Consultant, Blogger & Entrepreneur. Mr. Kiron is working as a textile consultant in several local and international companies. He is also a contributor of Wikipedia.
